Exercise Library
Floating Clean Deadlift On Riser
AKA Floating deficit clean deadlift
AKA Floating deficit clean deadlift
The floating clean deadlift on riser is a clean deadlift in which the lifter stands on an elevated platform and doesn’t allow the bar to touch the floor between reps.
Set the clean starting position tightly—it should be the same as from the floor, but with more knee and hip flexion. In other words, the same back angle but deeper—don’t simply hinge more at the hips.
Push with the legs through the whole foot against the floor similarly to a squat. Maintain even balance over the whole foot and actively keep the bar as close to the legs as possible, and maintain approximately the same back angle until the bar is past the knees. Once at lower to mid-thigh, open the hips as you finish extending the legs into a standing position.
Reverse the motion to lower the bar in the exact same positions as the way up. Bring the bar as close to the floor as possible without touching, then return to the top for the next rep. Make sure you maintain tension and balance as you change directions in the bottom to avoid unwanted shifting in position.
Notes
Conventionally the first rep of a set is taken from the floor as a normal rep; for example, in a set of 3, only the last 2 reps are technically floating.
Purpose
The floating clean deadlift on riser increases the strengthening of the pull from the floor and the postural strength of the first pull. The riser ensures full range of motion in the floating position, i.e. the lifter can reach the actual starting position (or deeper) in the bottom rather than stopping short as happens in a floating lift from the floor.
Programming
Generally the floating clean deadlift on riser should be done for 2-5 reps per set anywhere from 80%-110% of the lifter’s best clean. Newer lifters whose cleans are significantly limited by technique will likely need to pull much heavier percentages to adequately train strength in the pull. Because of the difficulty and continuous effort, loading will not quite reach what a lifter is capable of in a normal clean deadlift.
In any case, the weight should not exceed what the lifter can do with reasonably proper positioning—if being used for posture, position and balance training, weights need to be controlled to allow perfect positioning and movement. As a heavy strength exercise, it should be placed toward the end of a workout. Typically pulling exercises are performed before squats, but this order can be reversed for lifters who need to emphasize squat strength over pulling strength.
Variations
The floating clean deadlift on riser can be performed with slow eccentrics (3-6 seconds typically), with one or more pauses on the way up, with slow concentrics to emphasize control over posture and balance, with a pause in the floating position, with or without straps, and many other possibilities.
Set the clean starting position tightly—it should be the same as from the floor, but with more knee and hip flexion. In other words, the same back angle but deeper—don’t simply hinge more at the hips.
Push with the legs through the whole foot against the floor similarly to a squat. Maintain even balance over the whole foot and actively keep the bar as close to the legs as possible, and maintain approximately the same back angle until the bar is past the knees. Once at lower to mid-thigh, open the hips as you finish extending the legs into a standing position.
Reverse the motion to lower the bar in the exact same positions as the way up. Bring the bar as close to the floor as possible without touching, then return to the top for the next rep. Make sure you maintain tension and balance as you change directions in the bottom to avoid unwanted shifting in position.
Notes
Conventionally the first rep of a set is taken from the floor as a normal rep; for example, in a set of 3, only the last 2 reps are technically floating.
Purpose
The floating clean deadlift on riser increases the strengthening of the pull from the floor and the postural strength of the first pull. The riser ensures full range of motion in the floating position, i.e. the lifter can reach the actual starting position (or deeper) in the bottom rather than stopping short as happens in a floating lift from the floor.
Programming
Generally the floating clean deadlift on riser should be done for 2-5 reps per set anywhere from 80%-110% of the lifter’s best clean. Newer lifters whose cleans are significantly limited by technique will likely need to pull much heavier percentages to adequately train strength in the pull. Because of the difficulty and continuous effort, loading will not quite reach what a lifter is capable of in a normal clean deadlift.
In any case, the weight should not exceed what the lifter can do with reasonably proper positioning—if being used for posture, position and balance training, weights need to be controlled to allow perfect positioning and movement. As a heavy strength exercise, it should be placed toward the end of a workout. Typically pulling exercises are performed before squats, but this order can be reversed for lifters who need to emphasize squat strength over pulling strength.
Variations
The floating clean deadlift on riser can be performed with slow eccentrics (3-6 seconds typically), with one or more pauses on the way up, with slow concentrics to emphasize control over posture and balance, with a pause in the floating position, with or without straps, and many other possibilities.
